{Step-by-Step Sewing} DIY Bow Cushion

7:00 am
















Today's tutorial follows on from last weeks project. If you viewed that one, you're half way there already! Here's part two of my matching cushion set. Today, with bows. I do love a good bow.

****** IF YOU VIEWED LAST WEEK'S TUTORIAL - YOU CAN PROBABLY SKIP TO THE NEXT SET OF STARS. IF NOT, DO READ ON :) *****

What you will need:
A cushion insert 
(these can be bought in varying sizes or, you may have one you're looking to repurpose)

Fabric
(I'm using calico because it has the lovely natural, speckled colour tone I was after. This may not be the easiest fabric to work with if you are new to sewing as it frays really easily but I was going for the vintage / worn kind of look)

Measuring Tape

Ruler
Pen
Fabric Scissors
Sewing Pins
Matching Cotton and Bobbin
Sewing Machine


How to measure the fabric needed:

If you are buying a store bought cushion insert, the packaging may tell you like mine what sized cover they are designed to fit into. If not,  perhaps you are recovering an existing inner, fear not, here is how to measure...
  • Place your cushion down on a flat surface
  • Lay your measuring tape on the cushion, in the centre but hold the sides out. Visually take your measurement. You will notice if you lay your measuring tape across the liner from one seam to the other, your measurement will be a good couple of inches longer. We want the insert to sit nice and snug so the cushion is full and squishy, not sagging around baggy the sides
  • Take this width measurement (or the measurement given to you on the packaging), allow a 1 inch seam allowance
  • Take the height measurement, double it. Add 3 inches. Add another 1/2 inch for seams
My cushion insert was designed to fit a cover of 16" x 16" so my measurements were:
17" width
35.5" height

You will also need some extra fabric for your ruffles.
Take your length measurement and double it. Choose a width that will suit the type of ruffles you are doing. This is personal preference. (I chose 2x pieces at 3.5" and one at 6")

Starting the Cushion Cover
  • Measure out your fabric. I mark my measurements against my measuring tape, then join the lines with a solid ruler
  • Cut and iron
  • To each short edge of the fabric, iron a 1/2" each seam
  • Sew
  • Next, lay your fabric on your table top, seams facing the table, good side facing up
  • Measure from one short edge, half your original length measurement (For me, this is 8") Pin on each side and the middle at this point
  • From those pins, measure the original length (For me, 16") and mark with pins
  • This dictates the area in which we can decorate and show on the final cushion
**************************************************************************************
Creating the Bows
  • To create your bows, you're going to want to cut many extra pieces of fabric, around 30. You can make these any size your like but I suggest sticking top similar proportions as the ones I have made. (I tried varying sizes and these proportions seemed to create the nicest looking bows)
  • Cut around 30 rectangles of 15cm x 10cm (5.5" x 3.5")
  • It was an absolutely necessity to use pinking shears around all the edges of my rectangles  to prevent excess fraying but, depending on your fabric, you may be able to skip this part altogether
  • Holding the rectangle in your hand, turn one side of the shape from facing up towards you, to facing down towards the table. This is how we are going to create the bow shapes. It create s a nice flat surface across the middle to sew through that isn't too bulky
  • One bow at a time, twist them into shape and pin both sides onto your cushion cover. Start by pinning them horizontally down a vertical row
  • After each row, stitch each bow individually through the middle being sure to back stitch at both the start and end of your sewing line
  • On the next row you create, turn the bows so that they are lying vertically along the vertical line this time
  • Repeat this pattern until your entire cushion cover is covered
You should now have bustling ruffle bows a plenty!

Finishing the Cushion Cover
  • Lay your ruffles out on your cushion cover as you wish for them to appear and one by one, pin in place and sew. For the side ruffles, I sewed just to the side of my original stitch to avoid any bulkiness and for the middle feature ruffle, tried to follow the original stitch line as close as I could.
  • Next, with the ruffles still facing upwards on your table, fold over the top pieces of fabric until the pin line you marked previously
  • Fold up the second half or the fabric to create an overlap. This creates the envelope effect
  • Quickly doubled check your folding matches the measurements you need and pin the open sides into place
  • Sew along both open edges before turning the right way
  • A quick iron to smooth of the cushion cover and you can slide in your cushion insert!

You Might Also Like

0 comments